Skip to content
Close menu
Top Links
back
Top Links
Newsroom
10/28/21
Wolfsburg
Models
Story

How to make Halloween your ID.4 festival

With our cutting template you can easily give your pumpkin the look of our all-electric SUV.

Story: "How to make Halloween your ID.4 festival"
With our instructions you can create your pumpkin in ID.4 design.

Halloween is right around the corner, and whether you’re planning to celebrate indoors or outside, an easy way to get into the holiday spirit is to take on a pumpkin-carving challenge.

So get some pumpkins, and grab your carving tools to bring these Volkswagen-themed pumpkin designs to life. One decal features the instantly recognizable Volkswagen Bus, while the other carries the look of Volkswagen’s ID.4 electric SUV. 

Some carving tips in advance:

  • Use painter’s tape to hold the stencil in place and a washable marker to trace the outlines.
  • For both stencils, carve the cut-out sections (those that are black on the PDF) first. Once you’ve carved those pieces, leave them in place; this helps maintain pumpkin strength while you scrape away other sections.
  • Scraped-away but not completely carved-through sections are tricky. Start by using a craft utility knife to lightly trace the stencil outline. Then use a small sanding or linoleum carving tool to remove the topmost layers of the real or fake pumpkins.

And here’s how it’s done:

MATERIALS

  • At least 1 Pumpkin (the bigger, the better)
  • Tape
  • Washable marker, pins or awl
  • Sharp knife
  • Pumpkin-scraper tool or metal spoon
  • Craft utility knife
  • Small carving tool such as a pumpkin-carving tool, a linoleum-carving tool (for a real pumpkin), or a small sanding tool (for a fake pumpkin)
Story: "How to make Halloween your ID.4 festival"
Our stencil to cut out and scrape.

STEPS

  1. Cut a hole in the top or bottom of the pumpkin and clean out the inside, scraping the flesh thoroughly.
  2. Using the print size commands or a copier, size the stencil based on the size of the pumpkin. Print and transfer the stencil to the pumpkin. You can do this in one of two ways: Cut out the stencil pieces and tape them to the pumpkin. Trace around the stencil pieces using a washable marker. Tape the entire stencil sheet to the pumpkin. Use a pin or awl to poke through the stencil at the edges, tracing the lines where you will need to cut or carve.
  3. Using a sharp knife or a pumpkin-carving tool, cut through, front to back, the two holes in each of the “headlights.” Leave these sections in for now to give you a good anchor point for the rest of the shape.
  4. Using a craft utility knife, carefully trace the edges of the circle sections of the logo and the outlines of the horizontal grille section. Do not cut all the way through; simply cut through the surface. These are the sections in which you will scrape off the outer edge of the pumpkin to create depth and shadow. Using a craft utility knife to outline the scraped areas helps keep the area from splintering. Use a carving tool to “scrape” the outer skin of the pumpkin inside the lines you just cut.
  5. Remove the previously carved-out carved pieces; place a battery-operated candle inside the pumpkin.
Back to top
Topics
Press
Service
Subscription Services

The Volkswagen Newsroom is an open platform and offers comprehensive search options to all users.

If you would like to be kept informed about our press releases and stories you can also subscribe to our media information and e-mail newsletters.

Sign up
Products as well as Volkswagen AG distributors can be found at: www.volkswagen.de
© Volkswagen 2022

The specified fuel consumption and emission data have been determined according to the measurement procedures prescribed by law. Since 1st September 2017, certain new vehicles are already being type-approved according to the Worldwide Harmonized Light Vehicles Test Procedure (WLTP), a more realistic test procedure for measuring fuel consumption and CO2 emissions. Starting on September 1st 2018, the New European Driving Cycle (NEDC) will be replaced by the WLTP in stages. Owing to the more realistic test conditions, the fuel consumption and CO2 emissions measured according to the WLTP will, in many cases, be higher than those measured according to the NEDC. For further information on the differences between the WLTP and NEDC, please visit www.volkswagen.de/wltp.

We are currently still required by law to state the NEDC figures. In the case of new vehicles which have been type-approved according to the WLTP, the NEDC figures are derived from the WLTP data. It is possible to specify the WLTP figures voluntarily in addition until such time as this is required by law. In cases where the NEDC figures are specified as value ranges, these do not refer to a particular individual vehicle and do not constitute part of the sales offering. They are intended exclusively as a means of comparison between different vehicle types. Additional equipment and accessories (e.g. add-on parts, different tyre formats, etc.) may change the relevant vehicle parameters, such as weight, rolling resistance and aerodynamics, and, in conjunction with weather and traffic conditions and individual driving style, may affect fuel consumption, electrical power consumption, CO2 emissions and the performance figures for the vehicle.

Further information on official fuel consumption figures and the official specific CO2 emissions of new passenger cars can be found in the “Guide on the fuel economy, CO2 emissions and power consumption of new passenger car models”, which is available free of charge at all sales dealerships and from DAT Deutsche Automobil Treuhand GmbH, Hellmuth-Hirth-Str. 1, D-73760 Ostfildern, Germany and at www.dat.de.